毕业论文

打赏
当前位置: 毕业论文 > 外文文献翻译 >

注塑模具外文文献及中文翻译

时间:2018-05-19 16:51来源:毕业论文
abstract Mold temperature is a major factor in the quality of injection molding process. A high mold temperature setting is feasible to enhance the molding quality but prolongs the cooling time. Induction heating is the method currently used

abstract Mold temperature is a major factor in the quality of injection molding process. A high mold temperature setting is feasible to enhance the molding quality but prolongs the cooling time. Induction heating is the method currently used to heat the mold surface without increasing the molding cycle. However, one unresolved problem of induction heating is the proximity effect resulting from two adjacent coils with different current directions. The proximity effect substantially decreases heating efficiency, which then causes non-uniform heating. This effect is difficult to avoid in a single-layer coil. The most common solution, which is to use magnetic concentrators to reduce the proximity effect , does not obtain satisfactory results . In the novel magnetic shielding induction heating method developed in this study, heating method developed in this study, heating efficiency and temperature uniformity are enhanced by using ferrite materials to separate the conflicting magnetic fields caused by the repulsive proximity effect. Three typical single-layer coils are investigated in this study, including a reciprocated single-layer coil, a single-layer spiral coil,and a rectangular frame coil. Appropriate placement of ferrite materials on these induction coils successfully eliminated the proximity effect, increased the heating rate, and improved temperature uniformity.23045
© 2013 Elsevier Ltd. All rights reserved.
Keywords: Ferrite material 、Induction heating 、Magnetic shielding Proximity effect
In the injection molding process, mold temperature is an important factor in the quality of injection molding process. A high mold temperature setting is feasible to enhance the molding quality but increases the cooling time and parts' demolding temperature.To enable cavity filling under a high mold temperature and parts' ejection under low temperature, a varioterm process was developed for high-precision injection molding, thin-walled injection molding and micro-injection molding [1–3].The variotherm process dynamically controls the mold temperature, preheats the mold to a higher temperature before the melt enters the mold cavities, and then decreases the mold temperature to the ejection temperature after the cavities are filled.
Common mold heating approaches for a variotherm process include infrared heating [4,5], gas-assisted heating[6], thin-film resistance heating [7], resistance cartridge heating [8,9], steam heating [10], and induction heating [11–14]. The advantages of induction heating, in which only the mold surface is heated, include rapid heating and cooling, good controllability, energy saving, and allowing local heating. Compared with conventional oil heating, induction heating has better potential for increasing mold  temperature and reducing cycle time.
The induction heating method has been widely used in the various industrial manufacturing processes.Since the skin effect of induction heating concent rates the resulting Joule heating at the surface of processed workpiece, the surface can be heated by using a high- frequency current . Therefore, induction heating is an efficient variotherm process for injection molding . Studies show that induction heating rapidly increases mold surface temperature, substantially shortens cycle time [11] ,increases the molding ability of thin-walled injection molding and micro-injection molding [12] , improves the replication of micro-features [13] , and reduces the welding line defect of injection molding parts [14] .
Induction coil designs can be classified into four types: unmovable external hung- up type ,movable external hung- up type, wrapped type, and inserted type. The first type is easily implemented because the induction coil is independent of the processed workpiece. Chen[ 15] used induction heating to increase the surface temperature of injection molds and found that both heating rate and uniformity are satisfactory when the area of the processed workpiece is 100 mm × 100 mm. The movable external type can be either a fixed induction coil with a movable processed workpiece or a fixed processed workpiece with a movable induction coil. The former is more common,particularly in metal welding or surface treatment[16 –18].Inwrapped induction heating, induction coils are used to embed the whole work-piece. Chen[19] reported that wrapped induction heating is effective for injection molding. In the inserted type, the induction coils are placed behind cores and cavities so that the penetration effect and heat conduction provide indirect heating of the mold surface. This technique is superior in terms of reduced cycle time because the induction coils do not have to be moved. However, the placement of induction coils inside the molds requires consideration of the layout of the cooling channel,the layout of the ejection system, and the rigidity of the mold structure. 注塑模具外文文献及中文翻译:http://www.youerw.com/fanyi/lunwen_15966.html
------分隔线----------------------------
推荐内容