摘要本文主要就环氧丙烷的催化异构化制备烯丙醇进行了研究。以寻找高活性，高选择性的催化剂为目的，小范围内对于催化环氧丙烷异构化生成烯丙醇的催化剂进行了筛选。制备了多种催化剂，并且通过异构化实验体系对几类催化剂进行了催化性能检测和对比。通过实验，对比了制备条件、反应条件和催化条件对催化异构化的影响，结果表明，在测试的多种催化剂（例如：TiO2、磷酸锂、固体超强酸、X型分子筛、纳米Ag等）中，磷酸锂是最适用于该体系的催化剂；磷酸锂负载Au的催化剂催化性能好过磷酸锂负载Cu、Ag的催化剂；Au-Li3PO4催化剂的最佳锻烧温度为320℃；负载率2。80 wt。%的 Au-Li3PO4催化效果最好；该体系内的催化剂，最佳使用温度为300℃。78572
毕业论文关键词：催化剂 异构化 环氧丙烷 烯丙醇 转化率 活性
毕业设计说明书外文摘要
Title Screening of Propylene Oxide Isomerization Catalyst
Abstract This paper focuses on the preparation of the allyl alcohol by catalytic isomerization of propylene oxide。 In order to find the high activity and selectivity catalyst, we screened the catalysts about propylene oxide isomerization of allyl alcohol。 A variety of catalysts were prepared, and the activity of several kinds of catalysts were detected and compared by isomerization experiment system。 Through experiments the effects of preparation conditions, reaction conditions, catalysts on the catalytic isomerization were compared。 The results show that among the various catalysts tested (for example: TiO2, lithium phosphate, solid super acid, X-type zeolite, Nano-Ag, etc。), the lithium phosphate is most suitable for this catalyst system。 The active and catalytic performance of Au supported lithium phosphate catalyst was better than that of Cu and Ag as a catalyst for the loading of lithium phosphate。 Lithium phosphate optimum calcination temperature of the catalyst is 320 ℃。 The load rate of 2。80wt。 % of the catalytic effect of Au-Li3PO4 is the best。 The catalyst in this system, the optimum temperature used was 300 ℃。
Keywords：catalysts, isomerization propylene oxide, allyl alcohol, conversion rates
目 录 I
1绪论 1
1。1引言 1
1。2催化异构化的介绍及应用 2
1。2。1异构化的介绍及应用 2
1。2。2环氧丙烷异构化的介绍及应用 3
1。3烯丙醇的生产方法及应用 4
1。3。1烯丙醇的生产发法 4
1。3。2烯丙醇的应用 6
1。4本文研究的目的及意义 6
2实验 7
2。1实验装置及设备 7
2。1。1环氧丙烷异构化实验装置及设备 7
2。1。2数据分析与表征设备 8
2。1。3催化剂制备过程设备 9
2。2实验试剂及药品 9
2。3催化剂的制备 10
2。3。1 TiO2催化剂的制备 10
2。3。2 X型分子筛催化剂的制备 11
2。3。3 磷酸锂催化剂的制备 11
3结果与讨论 13
3。1环氧丙烷异构化机理 环氧丙烷异构化催化剂的筛选:http://www.youerw.com/huaxue/lunwen_90578.html