毕业论文移动版

摘要：撑挡是高速印刷机的主要部件之一，它的主要作用是支撑印刷机的两个墙板，保证两墙板的竖直，从而保证安装在两墙板上的各个滚筒水平，所以撑挡两端面精度要求较高。另外有些类型的撑挡还需安装导轨，对于撑挡上要安装导轨的面，其精度要求也很高。57214

分析了撑挡的定位和夹紧形式，确定多种类型撑挡同线加工的工艺设计方案，采用卧式三面钻铰同时加工的机床配置形式即组合机床。根据工艺内容和生产节拍要求，选择合适的切削用量；设计并选用相应的刀具、接杆、主轴箱、动力箱、滑台等机床零部件，完成零件工序图、加工示意图和机床联系尺寸总图以及相关三维图的设计。 

采用专用夹具对撑挡进行定位与夹紧，对夹具体不同功能的部件进行了具体分析，并且对夹具进行了相关的设计计算，绘制了夹具工程图，从而对其进行了三维建模。

毕业论文关键词：撑挡  工艺设计方案  组合机床  夹具  三维建模

The processing technology and equipment design of a series of automatic high-speed printing machine

Abstract: Brace is one of the main components of high speed printing machine, its main role is to support the printer's two wallboard, and ensure that the two vertical wall panel, so as to ensure the installation in two panels on each drum level, the two end surface accuracy should be higher. Other types of stays still need installation guide rail, as for the face of the block which is installed on the guide rail, which need high accuracy.

Analyzing the positioning and clamping form stays, determining the various types to stays the same thread machining process, using horizontal drilling hinge on three sides, processing machine tool configuration form combination machine tools at the same time. According to the request of technology content and production rhythm, select the appropriate cutting parameter; design and choose the corresponding tools, arbor, spindle box, power box, sliding table, such as machine tool parts, complete machine parts process diagram, processing schematic drawing, designing the contact size of general layout and the three dimensional figure .

Using special fixture to positioning and clamping of stays, to gives a detailed analysis of the specific function of different parts ,fixture for the related design calculation, and draw the jig engineering drawing, thus for the 3 d modeling.

Key words: stays, process designing, combination machine tools, jig 3 d modeling

目   录

第 1 章 绪论 .1

1.1瓦楞纸水性印刷机的现状.1

1.2瓦楞纸水性印刷机的发展方向2

1.3 课题来源..2

1.4 研究背景与意义..3

1.5 本课题的研究内容4

第 2 章 撑挡加工工艺设计 .5

2.1 撑挡的功用及加工要求 .5

2.2 撑挡的工艺分析..6

2.3 工艺的规程设计..6

2.3.1撑挡毛坯制造形式的确定7

2.3.2撑挡基面的选择..7

2.3.3撑挡工艺路线的确定.7

2.4撑挡加工的余量以及工序尺寸的确定9

2.5撑挡切削用量的确定..9

2.6 本章小结 10

第 3 章 撑挡组合机床总体设计 ..11

3.1撑挡组合机床的特点.11

3.2 撑挡组合机床总体布局.11

3.3 主轴箱设计 .12

3.3.1主轴箱的力学计算..13

3.3.2主轴箱电机型号的选择 13

3.3.3主轴箱轮廓尺寸.14

3.3.4主轴箱传动系统的设计.14

3.3.5主轴与接杆设计.14

3.4动力滑台的设计..20

3.5本章小结 .22

第 4 章 撑挡组合机床专用夹具设计 .23

4.1夹具设计的目的..23

4.2 夹具设计 23

4.3夹具三维设计.25 (责任编辑：qin)