毕业论文

打赏
当前位置: 毕业论文 > 外文文献翻译 >

模拟退火技术来设计英文文献和中文翻译(10)

时间:2022-10-09 23:06来源:毕业论文
E Ei 1 Ei f (X i 1) f (X i ) (48) The new state or design point Xi+1 can be found using the Boltzmanns probability distribution: Algorithm [22] The SA algorithm [22] can

ΔE  ΔEi 1 ΔEi  f (X i 1) f (X i )                   (48) 

The new state or design point Xi+1 can be found using the Boltzmann’s probability distribution: 

Algorithm [22] 

The SA algorithm [22] can be summarized as follows。 Start with an initial design vector X1 (iteration number i = 1) and a high value of temperature T。 Ge- nerate a new design point randomly in the vicinity of  the current design point and find the difference in function values: 

ΔE  Δfi 1 Δfi  f (X i 1) f (X i )                      (51) 

If fi+1  is smaller than fi  (with a negative value    of 

∆f), accept the point Xi+1 as the next design point。  Otherwise, when ∆f is positive, accept the point Xi+1 as the next design point only with a  probability exp(ΔE / kT ) 。 This means that if the value of a ran- domly generated number is larger than exp(ΔE / kT ) , accept the point Xi+1; otherwise, reject the point    Xi+1。 

P (E ) min1, e

ΔE 

kT   (49) 

This completes one iteration of the SA algorithm。 If 

The Boltzmann’s constant serves as a scaling factor in simulated annealing and, as such, can be  chosen as 1 for simplicity。 Note that if ∆E ≤ 0, Eq。 (49) gives P(Ei+1) = 1 and hence the point Xi+1 is always accepted。 This is a logical choice in the context of mi- nimization of a function because the function value at Xi+1, fi+1, is better (smaller) than at Xi, fi, and hence the design vector Xi+1 must be accepted。 On  the other  hand, when ∆E > 0, the function value fi+1 at Xi+1 is worse (larger) than the one at Xi。 According to most conventional optimization procedures, the point Xi+1 cannot be accepted as the next point in the iterative  process。 However, the probability of accepting the point Xi+1, in spite of its being worse than Xi  in    terms of the objective function value,  is  finite  (although it may be small) according to the Metropolis criterion。 

the point Xi+1  is rejected, then the process of gene-

rating a new design point Xi+1  randomly in the  vicinity of the current design point, evaluating the corres- ponding objective function value fi+1, and deciding to accept Xi+1  as the new design point, based on the use of the Metropolis criterion, Eq。 (50), is continued。 To  simulate the attainment  of  thermal  equilibrium at   every temperature, a predetermined  number  (n)  of  new points Xi+1 are tested at any specific value of the temperature T。 Once the number of new design points Xi+1  tested at any temperature T exceeds the value of n, the temperature T is reduced by a pre-specified fractional value c (0 < c < 1) and the whole process is repeated。 The procedure is assumed to have con- verged when the current value of temperature T is sufficiently small or when changes in the function va- lues (∆f) are observed to be sufficiently small。 The choices  of  the  initial  temperature  T,  the  number of 

iterations n before reducing the temperature, and the temperature reduction factor c play important roles in the successful convergence of the SA algorithm。 For  example, if the initial temperature T is too large, it re- quires a larger number of temperature reductions for  convergence。 On the other hand, if the initial tempe- rature is chosen to be too small, the search process  may be incomplete in the sense that it might fail to thoroughly investigate the  design  space  in locating the global minimum before convergence。 The tempe- rature reduction factor c has  a  similar  effect。  Too  large a value of c (such as 0。8 or 0。9) requires too much computational effort for convergence。 On the  other hand, too small a value of c (such as 0。1 or 0。2) may result in a faster reduction in temperature that  might not permit a thorough exploration of the design space for locating the global minimum solution。 Si- milarly, a large value of the number of iterations n will help in achieving quasi equilibrium state at each tem- perature but will result in a larger computational effort。 A smaller value of n, on the other hand, might result either in a premature convergence or convergence  to a local minimum (due to inadequate exploration of the design space for the global minimum)。 Unfortunately, no unique set of values is available for T, n, and c that will work well for every problem。 As per recommen- dation of Rao [22], the initial temperature T can be chosen as the average value of the objective function computed at a number of randomly selected points in the design space。 The number of iterations n can be  chosen between 50 and 100 based on the computing resources and the desired accuracy of solution。 The  temperature reduction factor c can be chosen be- tween 0。4 and 0。6 for a reasonable temperature re- duction strategy (also termed the cooling schedule)。  More complex cooling schedules, based on the ex- pected mathematical convergence rates, have been  used in the literature for the solution of complex prac- tical optimization problems。 In spite of all the research being done on SA algorithms, the choice of the initial temperature T, the number of iterations n at any spe- cific temperature, and the temperature reduction fac- tor (or cooling rate) c still remain an art and generally require a trial-and-error process to find suitable va- lues for solving any particular type of optimization  problems。 The SA procedure is shown as a  flowchart in Figure 2 [22]。  模拟退火技术来设计英文文献和中文翻译(10):http://www.youerw.com/fanyi/lunwen_100221.html

------分隔线----------------------------
推荐内容