毕业论文

打赏
当前位置: 毕业论文 > 机械论文 >

ADAMS某火炮供弹机动力学分析与仿真

时间:2019-01-19 19:48来源:毕业论文
基于SolidWorks软件对供弹机的具体结构进行设计和建模,通过动力学仿真软件ADAMS对供弹机模型进行具体的性能以及结构分析,最后利用ADAMS和MATLAB/Simulink开展联合仿真

摘要本文以某火炮供弹机为研究对象,通过查阅当前国内外关于供弹机介绍的文献资料,阐述供弹机的工作原理,在对协调供弹机功能了解的基础上,根据火炮供弹机的设计原理,给定相关条件,参考现有的供弹机,基于SolidWorks软件对供弹机的具体结构进行设计和建模,通过动力学仿真软件ADAMS对供弹机模型进行具体的性能以及结构分析,最后利用ADAMS和MATLAB/Simulink开展联合仿真,获得供弹运动过程中机构的动态响应以及震动状态和运动规律,并对仿真结果进行分析,得到满足设计要求的供弹机系统。32956
关键词  供弹机系统  建模  MATLAB/Simulink  SolidWorks  ADAMS  联合仿真等
毕业论文设计说明书外文摘要
Title  Dynamics Analysis and Control of a Certain Artillery Ramming System                            
Abstract
An ammunition supplying mechanism of a certain artillery was studied in this thesis, and the working principle of the ammunition supplying mechanism was introduced through the review of current domestic and foreign literatures. Referred to the the available ammunition supplying mechanism, the structural model was designed and established in SolidWorks software according to the design principle and the given relevant conditions, based on a good understanding of its function. The specific performance and structural analysis of the ammunition supplying mechanism model were conducted using dynamic simulation software ADAMS. Then, the ADAMS and MATLAB/Simulink softwares were used to suceed co-simulation of the ammunition supplying mechanism model, thus the dynamic response, vibration state and motion law during ammunition feed were obtained.Finally, the ammunition supplying mechanism satisfied the design requirements were developed and established based on the analysis of simulation results.
Keywords  ammunition supplying mechanism  modelling  MATLAB/Simulink  SolidWorks  ADAMS  Co-simulation
目   次
1  引言    1
1.1  选题背景    2
1.2  国内外研究现状    2
1.3  本文的主要工作    5
2  供弹机三文实体模型    6
2.1  供弹机部分零件三文实体模型    6
2.1.1  供弹机中弹仓相关零件的三文实体模型    6
2.1.2  供弹机中弹仓的三文实体模型    8
2.1.3  供弹机中组成主动轴、从动轴的零件的三文实体模型    9
2.1.4  供弹机中主动轴、从动轴的三文实体模型    11
2.2  装配后的供弹机零件实体模型    12
2.3  供弹机整体装备模型的导入    12
3  供弹机动力学建模与仿真分析    14
3.1  ADAMS软件介绍    14
3.2  供弹机系统的建模与仿真分析    14
4  ADAMS与MATLAB联合仿真    17
4.1  ADAMS/Controls模块    17
4.2  MATLAB/Simulink工具箱[    17
4.3  ADAMS以及Simulink联合仿真步骤    19
4.3.1  构造ADAMS样机模型[11]    19
4.3.2  确定ADAMS的输入输出[14]    19
4.3.3  用MATLAB/Simulink构造控制系统框图    23
4.4  MATLAB+ADAMS联合仿真    23
4.5  联合仿真结果分析    24
结  论    30
致  谢    31
参考文献    32 ADAMS某火炮供弹机动力学分析与仿真:http://www.youerw.com/jixie/lunwen_29767.html
------分隔线----------------------------
推荐内容