中文摘要:本次毕业设计题目FA-SV-TS-L平板式直线电机实训台电气控制系统设计，是针对目前大学机械专业学生对数控车床的理解不深，实际操作经验不足，所设计的项目。我们本次设计的数控实训台集合了数控加工的特点，以及基本一些电路故障的特点。在数控实训加工课程还未全面普及的情况下，这次设计成果是有一定价值的。41369
   前期通过对数控实训台需要满足技术要求的统计，确定基本的设计思路，再根据基本数据计算电机选型，根据需要满足的控制要求，确定控制方式是由PLC控制，根据PLC的特点和优势来整合编排需要控制的地址数量，设计好控制电路，同时也要满足学生对机器进行操作的方便和快捷，良好的人机界面设定也是相当有必要的，于是在经过大量的查阅以及经验，基本确定了PLC电路对系统的控制。
   最后对复杂电路图的安排和设计，需要进行大量的资料文献查找和对比各种电路控制的优势和特点，最后进行设计和绘制
毕业论文关键词: 直线电机、数控系统、实训台、电气控制系统、电路图、PLC、
英文摘要：
   The graduation design topic FA - SV - TS - L plate type linear motor training machine electrical control system design, is based on the current university mechanical professional students of deep the understanding of the numerical control lathe, the lack of practical experience, the design of project. We the design of numerical control practice brings together the characteristics of nc machining, and some basic circuit fault characteristics. In the nc training course has not yet universal, the design results has a certain value.
   Prophase of numerical control practice need to meet the technical requirements, determine the basic design idea, according to the basic data to calculate motor selection, according to the need to meet the control requirements, determine the control mode is controlled by PLC, according to the characteristics of the PLC and advantage to integrate choreography need to control the number of addresses, good control circuit design, but also to meet the student to the machine to operate convenient and quick, good man-machine interface set is quite necessary, so after a lot of reference and experience, the basic circuit of the system determines the PLC control.
The arrangement and design of complex circuit diagram, a lot of information literature search and comparative advantages and characteristics of various circuit control, the final design and drawing
Keywords: linear motor, CNC system, training table, electrical control systems, circuit diagram, PLC,
目录
   引言    2
一 数控机床简介    2
1.1国外数控机床技术现状     2
1.2国外机床数控系统技术现状     3
1.3.国外数控系统的发展趋势4种类型     3
1.4.电气控制系统简介    4
二 主电路控制    5
2.1主轴电机 - 主轴电机与伺服电机的区别     5
2.1.1数控机床对进给伺服电机的要求主要为    5
2.1.2对主轴电机的要求主要为    5
2.2变频器    5
2.3直线电机     6
2.4关于散热的问题     7
2.5电气控制图设计    8
2.5.1主轴控制系统简介     8
2.5.2步进电机的工作原理     9
2.5.3 主轴电机启动    9
三 进给驱动系统与检测系统    10
3.1伺服电机     10
3.1.1伺服电机的特点     10
3.1.2 交流伺服电机    10
3.2同步电机     11 FA-SV-TS-L平板式直线电机实训台电气控制系统设计+CAD图纸:http://www.youerw.com/jixie/lunwen_41388.html