摘要四象限探测器（QD）结构简单，只需四个光电特性一致的光电二极管直角坐标排列，却能用来精确测定角度，方位。灵敏度高，信号运算电路简单，主要计算在算法模拟仿真上。所以在现代诸多领域都有所建树，如激光准直，准直激光可以应用于定向通信，掩膜预对准，制导武器，两种类型制导，主动，半主动，不过都需要接收器，可以应用四象限探测器。73353
本文引言讨论了PSD，CCD与四象限定位的差别，各自在不同邻域发挥光芒，为其各自适用方面做了概述。73353
本论文主要研究均匀光斑在四象限探测器中的特点，高斯光斑略做分析，并提供了高斯光斑的（高斯函数）仿真模型。通过MATLAB仿真得到与光斑位置与光照面积的关系。然后通过探测器到通光孔的距离结合光斑位置得出它相对于通光孔到相探测器中心原点为中心轴的二维相对角度位移量（通过系统结构变化可以化为测镜面或其它物体角度偏移，核心）。用verilog设计经过放大电路和数模转化后的电压运算电路。用由电压运算电路输出的数值从仿真拟合曲线中找出位移量。
对于主要内容用MATLAB仿真了四种算法特点。根据所选用的对于光强分布均匀的圆形光斑的仿真算法。本文中最准确的是加减算法，后三种△/ 算法，对数，对角所选用面积模型都是近似模型（舍弃了Y（或X）分量对光面积的影响），虽然对角线方法线性范围比加减算法大了 ，但本文为使各X轴长度相同（方便将除对数算法外的图放于一张中做对比），线性范围规定为2r。
在选择参数方面，根据探测器半径和光斑半径（结合线性范围）选取特点将其光斑半径归一化设为1。同时舍弃了X,Y轴上暗区误差。
毕业论文关键词 四象限探测器 测角算法 仿真模拟
Title:Angle measurement of the Four quadrant detector
Abstract The four quadrant detector (QD) is simple in structure, and can be used to accurately determine the angle and azimuth of the photoelectric diode with four photoelectric characteristics。 High sensitivity, simple signal circuit, the main calculation in the algorithm simulation。 So in many modern fields to accomplish something, such as laser collimation, laser alignment can be applied to the directional communication, mask pre alignment, guided weapons, two types of guidance, initiative, semi active), but to the receiver, using four quadrant detector。
In this paper, the difference of PSD, CCD and four quadrant location is discussed, and the light is played in different neighborhoods, and the respective application aspects are summarized。
In this paper, we mainly study the characteristics of uniform spot in the four quadrant detector, and the Gauss spot is analyzed, and the simulation model of Gauss's spot (Gauss function) is provided。 The relationship between the spot position and the illumination area is obtained by MATLAB simulation。 Then through the detector to pass light hole distance and spot position that it is relative to the light through hole to phase detector center origin for the central axis of the two-dimensional relative angular displacement (through the change of the structure of the system can be as a measuring mirror or other objects angle offset, the core)。 The voltage operation circuit is designed by using Verilog after amplification circuit and digital analog conversion。 By using numerical output voltage of circuit operation from the simulation curve fitting for displacement。
The main content of the MATLAB simulation with the characteristics of the four algorithms。 According to the simulation algorithm of circular spot with uniform distribution of light intensity。 In this paper the most accurate is addition and subtraction algorithm, after three] / algorithms, logarithmic, diagonal selected area model are approximation model (abandoning the Y (or x) component of light area effect), although the diagonal linear range than the addition and subtraction algorithm, but this is the X axis length the same as (the except algorithm with a logarithmic graph put in a contrast)。 The linear range of provisions for 2R。 四象限探测器的测角算法研究MATLAB仿真:http://www.youerw.com/tongxin/lunwen_83679.html