菜单
  

    4 Configuration

    4.1 Configuration options

    An S7-200 system can communicate with another S7-200 system and with anS7-300, S7-400 or OPC-based system via the CP 243-1A.

    There are two methods of configuring a communication of this type in an S7-200 system: 49484

    • Configuration using STEP 7 Micro/WIN 32, version 3.2.1 or higher

    • Configuration using an S7-200 user program

    Attention

    The system can only be configured via an S7-200 user program if the CRC

    mechanism has been switched off.

    Since the configuration data can no longer be fully checked for consistency with

    regard to intended and unintended changes after the CRC check of the CP 243-1

    has been switched off, there can be no guarantee in this case that the CP or the

    components connected in the network will operate correctly.

    In both cases, the configuration data is stored in the data block of the S7-200 CPU.

    Every time the CP 243-1 is restarted, the data is read once from that location.

    Attention

    To protect the configuration data of the CP 243-1 if the system goes into a novoltage

    state, these data must be stored in a non-volatile data storage area of the

    S7-200 CPU.

    In a standard S7-200 system, the entire data block is defined as non-volatile. However,

    this default setting on your S7-200 system could have been modified if

    changes were made to the configuration.

    If STEP 7 Micro/WIN 32 is used for reconfiguring or modifying the configuration of

    the CP 243-1, the new configuration becomes effective only after the CP 243-1 is

    restarted. If the S7-200 CPU changes from STOP to RUN mode after such a reconfiguration,

    the CP 243-1 is automatically restarted. However, if the CP 243-1 is

    configured directly in the S7-200 user program, the configuration can be enabled

    by calling up the "ETHx_CFG" subroutine in the user program. Calling up the subroutine

    also causes the CP 243-1 to restart.

    The TCP/IP address parameter (IP address, subnet mask, IP address of a Gateway)

    can either be defined during configuration or the CP 243-1 can be configured

    in such a way that it dynamically retrieves the TCP/IP address parameters from a

    BOOTP server while booting.

    If an S7-200 system is to communicate with an S7-300, S7-400 or OPC-based system

    via a CP 243-1, configure such an S7-300, S7-400 or OPC-based system using

    STEP 7, version 5.1 or higher, with Service Pack 3 or higher (with NCM S7 for

    Industrial Ethernet).

    Note

    The CP 243-1 may independently switch to another Gateway after booting due to

    special network-based services ("ICMPRedirect"). After approx. 30 seconds, the

    CP 243-1 switches back to the Gateway originally configured. Thus, the Gateway

    actually used by CP 243-1 can temporarily deviate from the one defined in the configuration.

    You can read out the Gateway the CP 243-1 is using at any particular time from the

    storage area of the S7-200 CPU in which the NPB data block is stored (see Chapter

    4.4.3). To do so, use the CP 243-1 diagnostics window in STEP 7 Micro/WIN 32

    or make use of a user program.

     

    4.2 Value ranges of the configuration data

    4.2.1 IP address

    The IP addresses to be specified at various points within the configuration must

    comply with the general conventions defining IP address validity.

    According to these conventions, certain IP addresses serve specific purposes.

    These addresses will not be accepted by the CP 243-1. They include:

    • Loopback: 127.0.0.0 - 127.255.255.255

    • "Class D" addresses: 224.0.0.0 - 239.255.255.255

  1. 上一篇:振动台实验和动态响应地震后的钢筋混凝土建筑英文文献和中文翻译
  2. 下一篇:机床结构动态性能预测英文文献及中文翻译
  1. 汽车内燃机连杆载荷和应...

  2. 机械手系统英文文献和中文翻译

  3. 固体氧化物燃料电池英文文献和中文翻译

  4. 船舶运动仿真系统英文文献和中文翻译

  5. 新能源空调系统设计英文文献和中文翻译

  6. 正交试验回归法和响应曲...

  7. 机械设计制造及其自动化英文文献和中文翻译

  8. NFC协议物理层的软件实现+文献综述

  9. 上市公司股权结构对经营绩效的影响研究

  10. 高警觉工作人群的元情绪...

  11. 现代简约美式风格在室内家装中的运用

  12. C++最短路径算法研究和程序设计

  13. 巴金《激流三部曲》高觉新的悲剧命运

  14. 江苏省某高中学生体质现状的调查研究

  15. g-C3N4光催化剂的制备和光催化性能研究

  16. 中国传统元素在游戏角色...

  17. 浅析中国古代宗法制度

  

About

优尔论文网手机版...

主页:http://www.youerw.com

关闭返回