菜单
  
    Introduction Heat exchangers have always been an important part to the lifecycle and operation of
    many systems. A heat exchanger is a device built for efficient heat transfer from one medium to
    another in order to carry and process energy. Typically one medium is cooled while the other is
    heated. They are widely used in petroleum refineries, chemical plants, petrochemical plants,
    natural gas processing, air-conditioning, refrigeration, and automotive applications. One com-
    mon example of a heat exchanger is the radiator in a car, in which it transfers heat fromthe water
    (hot engine-cooling fluid) in the radiator to the air passing through the radiator.7681
    There are two main types of heat exchangers:
    – direct contact heat exchanger, where both media between which heat is exchanged are in
    direct contact with each other, and– indirect contact heat exchanger, where both media are separated by a wall through which
    heat is transferred so that they never mix.
    A typical heat exchanger, usually for higher pressure applications up to 552 bar, is the
    shell and tube heat exchanger. Shell and tube type heat exchanger is an indirect contact type heat
    exchanger as it consists of a series of tubes, through which one of the fluids runs. The shell is a
    container for the shell fluid. Usually, it is cylindrical in shape with a circular cross-section, al-
    though shells of different shapes are used in specific applications. For this particular study E
    shell is considered, which is generally a one pass shell. E shell is themost commonly used due to
    its low cost and simplicity, and has the highest log-mean temperature-difference (LMTD) cor-
    rection factor. Although the tubes may have single or multiple passes, there is one pass on the
    shell side, while the other fluid flows within the shell over the tubes to be heated or cooled. The
    tube side and shell side fluids are separated by a tube sheet, [1-3]. The heat exchanger model
    used in this study is a small sized one, as compared to the main stream, all of the leakage and by-
    pass streams do not exist or are negligible, [4-6]. Baffles are used to support the tubes for struc-
    tural rigidity, preventing tube vibration and sagging and to pert the flow across the bundle to
    obtain a higher heat transfer coefficient. Baffle spacing (B) is the centre line distance between
    two adjacent baffles, [7-9]. Baffle is provided with a cut (Bc) which is expressed as the percent-
    age of the segment height to shell inside diameter. Baffle cut can vary between 15% and 45% of
    the shell inside diameter, [10-12]. In the present study 36% Bc is considered. In general, con-
    ventional shell and tube heat exchangers result in high shell-side pressure drop and formation of
    re-circulation zones near the baffles.Most of the researches now a day are carried on helical baf-
    fles, which give better performance then single segmental baffles but they involve high manu-
    facturing cost, installation cost and maintenance cost. The effectiveness and cost are two impor-
    tant parameters in heat exchanger design. So, In order to improve the thermal performance at a
    reasonable cost of the shell and tube heat exchanger, baffles in the present study are provided
    with some inclination in order tomaintain a reasonable pressure drop across the exchanger [13].
    The complexity with experimental techniques involves quantitative description of
    flow phenomena using measurements dealing with one quantity at a time for a limited range of
    problem and operating conditions. Computational fluid dynamics (CFD) is now an established
    industrial design tool, offering obvious advantages [14]. In this study, a full 360° CFD model of
    shell and tube heat exchanger is considered. By modeling the geometry as accurately as possi-
    ble, the flow structure and the temperature distribution inside the shell are obtained.
  1. 上一篇:阀重量对于阀塔性能影响CFD模拟英文文献和中文翻译
  2. 下一篇:注塑模CAE技术英文文献和中文翻译
  1. 升式单位上升操作结构英文文献和中文翻译

  2. 绞盘式绞车英文文献和中文翻译

  3. 套筒弹簧式扭振减振器制...

  4. 桥式起重机智能防摆控制英文文献和中文翻译

  5. 撑开式闸阀设计英文文献和中文翻译

  6. 离岸自升式单元非线性动...

  7. 自升式平台锁定装置英文文献和中文翻译

  8. C++最短路径算法研究和程序设计

  9. 上市公司股权结构对经营绩效的影响研究

  10. 巴金《激流三部曲》高觉新的悲剧命运

  11. 中国传统元素在游戏角色...

  12. 浅析中国古代宗法制度

  13. NFC协议物理层的软件实现+文献综述

  14. 高警觉工作人群的元情绪...

  15. 现代简约美式风格在室内家装中的运用

  16. g-C3N4光催化剂的制备和光催化性能研究

  17. 江苏省某高中学生体质现状的调查研究

  

About

优尔论文网手机版...

主页:http://www.youerw.com

关闭返回