摘要为减少切削液排放对环境造成的污染，促进金属切削技术绿色、高效、高速发展，并提高钛合金等难加工材料的加工效率，延长刀具寿命，利用有限元软件DEFROM-3D通过对Ti-6Al-4V本构模型、摩擦模型、刀-屑接触摩擦和热传导模型等关键物理环节建模,建立了其冷风切削的三维建模，并对切削过程进行了仿真。采用单因素试验法，模拟分两部分进行，一是：在相同参数与冷风温度下通过改变切削速度，得出切削力、切削温度的变化规律。二是；在相同参数与切削速度下对干切削和低温冷风切削的切削力、切削温度进行分析。仿真结果表明：增加切削速度，会引起切削温度的升高，但对主切削力影响很小；相比干切削，采用低温冷风切削能有效降低切削温度，且冷风切削力稍高于干切削。49736
毕业论文关键词：钛合金；冷风切削；切削力；切削温度；有限元法
Abstract In order to reduce emissions cutting fluid to environmental pollution, promote the metal cutting technology, high efficiency, high speed development green, and improve the titanium alloy processing materials to processing efficiency, extend the life of cutter, the finite element software DEFROM-3 D through to Ti-6 Al-4 V constitutive model, friction model, knife-flocks contact friction and heat transfer model and key physical link modeling, established the cold wind of cutting of 3 D modeling, and the cutting process simulation. The single factor experiment method, simulation is pided into two parts, one is: in the same parameters and the cold wind temperature by changing the cutting speed, and concludes that the cutting force, the change rule of cutting temperature. 2 it is; In the same parameters and cutting speed of dry cutting under low temperature and the cold wind of cutting of cutting force, cutting temperature for analysis. The simulation results show that increase cutting speed, can cause cutting the temperature increases, but for the Lord had little effect on cutting force; Compared with dry cutting, low temperature cold wind cutting can effectively reduce the temperature of cutting, cutting force and the cold wind slightly higher than that of dry cutting.
Key words: Titanium alloy; The cold wind cutting; Cutting force; Cutting temperature; Finite element method
目 录
第一章 绪论 6
1.1 冷风切削技术的发展应用及课题 6
1.1.1 金属切削基本技术的进步 6
1.1.2 低温空气代替切削剂 6
1.1.3 冷风切削技术及加工系统 7
1.1.4 冷风切削效益 8
1.2.1 冷风切削技术的实验研究 9
1.2.2 金属切削过程的三维有限元分析 11
1.3 钛合金分析 11
1.4 本论文研究目的、意义 12
1.5 本论文研究的主要内容 13
第二章 冷风切削过程有限元仿真技术 14
2.1 材料模型的建立 14
2.2 刀屑界面摩擦模型的建立 14
2.3 热传导模型及冷源的添加 15
2.3.1 热传导模型 15
2.3.2 冷源的添加 16
2.4 网格重划分 16 DEFROM-3D冷风切削加工过程三维建模与仿真:http://www.youerw.com/jixie/lunwen_52826.html