毕业论文

打赏
当前位置: 毕业论文 > 机械论文 >

130mm固冲增程制导炮弹内弹道计算

时间:2019-01-19 19:35来源:毕业论文
130mm固冲增程弹就利用了固冲发动机,能提高炮弹的射程,有较高的飞行速度,缩短了全弹道飞行时间,具有很好的发展潜力。本论文对130mm固体燃料冲压增程制导炮弹的内弹道进行了研

摘要固体燃料冲压发动机是自身含有燃料,利用空气进行燃烧的新型发动机,本次计算的130mm固冲增程弹就利用了固冲发动机,能提高炮弹的射程,有较高的飞行速度,缩短了全弹道飞行时间,具有很好的发展潜力。本论文对130mm固体燃料冲压增程制导炮弹的内弹道进行了研究。32954
    针对固体燃料冲压发动机内弹道的特点,将内弹道的计算分为四个部分:1、圆锥绕流计算,包括求解激波角、穿越斜激波的计算、从斜激波后到锥面的等熵压缩过程的计算;2、进气道内部流动的计算,包括正激波前和正激波后的一文变截面等熵流动和穿越正激波的计算;3、燃烧室的计算,包括燃烧室热力计算、等截面加热管流计算;4、喷管流动的计算,包括收敛段的计算,扩张段的计算。
用VB编写了具有计算上述过程的软件,可以迅速得出四个部分所需的参数,对固冲压增程制导炮弹的相关设计提供指导和参照。
关键词 :固体燃料冲压发动机,内弹道计算
毕业论文设计说明书外文摘要
Title      The Internal Ballistics Calculation of 130mm  Solid   fuel ramjet                                                      
Abstract
Solid fuel ramjet is a carrying fuel, the use of oxygen in the air of the new air-breathing combustion engine, This study 130mm solid fuel ramjet extended range projectile on the use of solid fuel ramjet, it can greatly improve the artillery range, and has a higher flight speed, thus shortening the whole trajectory of flight time, having broad application prospects. In this thesis, internal ballistics 130mm solid fuel stamping Extended Range Guided Munition were studied.
For within the solid fuel ramjet ballistic characteristics of the interior ballistics calculation is pided into four parts: 1, the conical flow around computing, including the solution of the shock angle, through the oblique shock wave calculations, from the oblique shock wave to the cone isentropic compression calculation process; (2) the calculation of the internal flow inlet, including the entropy flow and the calculation of normal shock through a normal shock dimensional change before and after the normal shock cross section; 3, the calculation of the combustion chamber, including combustion thermodynamic calculation, and other cross-sectional heating pipe flow calculations; 4, nozzle flow calculation, including the convergence of computing segment, the expansion segment.
VB prepared by the software has calculated the above processes, the required parameters can be quickly drawn into four parts, the relevant design solid fuel stamping Extended Range Guided Munition provide theoretical guidance and reference.
Keywords SFRJ,Internal ballistics
目  次
1 绪论    1
1.1研究背景及其意义    1
1.2固体燃料冲压发动机的分类与工作特点    1
1.3 固体燃料冲压增程炮弹国內外研究现状    2
1.4  本学位论文的主要研究内容    5
2固体燃料冲压发动机内弹道的计算    6
2.1固体燃料冲压发动机工作过程及结构    6
2.1.1 固体燃料冲压发动机的结构    6
2.1.2 进气道    7
2.1.3  燃烧室    8
2.1.4  尾喷管    10
2.2固体燃料冲压发动机内弹道模型    11
2.3固体燃料冲压发动机内弹道计算示意图    12 130mm固冲增程制导炮弹内弹道计算:http://www.youerw.com/jixie/lunwen_29763.html
------分隔线----------------------------
推荐内容