毕业论文移动版

摘要针对市场上育秧制钵机传动系统较为复杂，成本较高等缺陷，通过调研和优化，提出一种新的设计方案，有效提高育秧制钵机使用性能和生产效率。新的方案从传动系统设计到各个执行机构的尺寸设计和强度校核，严格遵照现代设计规范，分析和计算详尽、准确。尽量使用螺栓等标准件，缩短设计周期并降低制造成本。本文围绕工艺方案与传动装置、运动和动力设计和结构设计三大方面进行新机器详细设计，绘制出部分零件的零件图和装配总图。最后给出重要零件的三维实体造型和传动机构的运动仿真。新型育秧制钵机拥有良好的防尘性能，对动力源要求不高，搬运方便，适合全国大范围使用。作为方便培育秧苗和提高秧苗质量的重要措施，合理地设计并广泛地应用育秧制钵机对实际农业生产有着重大的现实意义。49744

毕业论文关键词：育秧制钵机; 三维实体造型; 运动仿真

Abstract Nursery pot making machine transmission system on the market are more complex, expensive, by research and optimization, coming up with a new design, and effectively improving the performance and productivity of nursery pot making machine.New programme design to the dimensions of the inpidual executive body from the transmission system design and strength check, strictly follows the modern design specification,and analysis and calculation are detailed and accurate. Making most use of bolts and other standard parts in order to short design cycles and reduce manufacturing costs,this paper focuses on the three aspects which contains the technology programs and gear, movement and power design and structural design, so as to make detailed design of the new machine,then drawing out part of the component graphs and assembly diagram.Last draw out vital parts of three dimensional solid modeling and motion simulation of the transmission mechanism. New nursery pot making machine has good performance, and power requirements are not high; it is easy to carry, suitable for widespread use throughout the country. As important measures to facilitate the cultivation of seedlings and raising seedling quality, reasonable design and widely used nursery pot making machine on practical agricultural production is of great realistic significance.

Keywords:nursery pot making machine; three dimensional solid modeling; motion simulation 

目录

第一章 绪论 1

1.1 育秧钵制钵机概述 1

1.2 国内外研究现状 1

第二章 工艺方案与传动装置 2

2.1 工艺方案分析与传动装置确定 2

2.1.1 手工制育秧钵工艺 2

2.1.2 老式制育秧钵机 2

2.1.3 改进后方案确定 3

2.2 原理图与系统图设计 4

第三章 运动和动力设计 6

3.1 电动机的确定 6

3.2 安排传动机构传动比 7

3.3 各轴转速和功率确定 8

第四章 结构设计和尺寸计算 10

4.1 模孔转盘结构和尺寸 10

4.1.1 基本尺寸预确定 10

4.1.2 强度校核 12

4.2 偏心轮滑杆结构和尺寸 15

4.2.1偏心距的确定 15

4.2.2 确定连杆的长度和尺寸 (责任编辑：qin)