- 上一篇：颚式破碎机的英文参考文献和翻译
- 下一篇：医院手术室室内空气英文文献和中文翻译
5 BIT Climber and Experimental Tests
An SWCR prototype called “BIT Climber” was developed for test, its mechanical structure is shown in Fig 5.
Fig. 5. Exploded view of BIT Climber
Considering the tradeoff of adsorption performance and controlling difficulty, b type, namely 2 driven wheels and 2 passive wheels as described in section 2.1, is used as locomotion mechanism. The robot uses a flexible rubber mat combined with a hair ring as sealing device. The rubber has big flow resistance, and its appropriate flexibility helps
the robot to accommodate small obstacles in motion. The hair ring is an ascendant throttling device, it has powerful .
For the purpose of designing a suitable impeller, the fluid environment where the robot works should be specified, after evaluation we set effective negative pressure to be 3 kPa, flow rate 0.02 m3/s. The method presented in section 4 is followed for impeller primary selection, simulation and analysis. Finally, an impeller, with D2 = 95 mm, D1 = 42 mm, B2 = 9.2 mm, B1 = 15 mm, β2A = 30,β1A = 15,Z = 9, is manufactured and mounted in the robot.
Experiments were conducted to evaluate the performance of Bit Climber. The specifications are listed in Table 2. It was demonstrated that BIT Climber is able to move on various wall surfaces to perform its task, the working surfaces include brick, glass, metal, stucco, wood and plaster, see Fig. 6
Fig 6. BIT Climber at work with a load of 59N
The adsorption force Fa is 208 N, of which 9 N is Fss, 30 N is Fsp, the utilization rate of adsorption force is 81%. Average vacuum in the sucker is 2.94 kPa, electric power of impeller shaft is about 150 W, reaching a relatively high utilization rate of power of about 84%.
6 Conclusions and Developing
6.1 Conclusions
(1) The paper illustrates how mobile mechanism and pressure allocation for sealing device influence SWCR’s utilization rate of adsorption force, providing a theoretical basis for relevant parameters selection.
(2) Suction system’s thermodynamics and hydrodynamics analysis is presented, which shows that reducing flow rate and improving the efficiency of impeller are directions for improving utilization rate of power.
(3) The paper comes up with a design method for SWCR-specific impeller, in which outlet installation angle and static pressure ratio are two key parameters that impact its aerodynamic performance.
(4) Through development of prototype and experiments,
conclusions above are verified. Future work focuses on the
premise of good maneuverability and adsorption
performance, how to reduce flow rate to save power
remarkably.
6.2 Developing
Climbing robot is capable of operating in a vertical cliff robot , which serves as an automatic altitude limit job mechanical device , more and more people 's attention. To sum up, wall-climbing robot is mainly used for :
-
双足步行机器人英文文献和中文翻译
-
脑电图像P300机器人手臂运...
-
机器人运动模糊逻辑控制英文文献和中文翻译
-
机器人控制系统英文文献和中文翻译
-
水下机器人AUV叶片冷锻钉...
-
机器人学入门力学与控制英文文献和中文翻译
-
弧焊机器人传感器英文文献和中文翻译
现代简约美式风格在室内家装中的运用
江苏省某高中学生体质现状的调查研究
巴金《激流三部曲》高觉新的悲剧命运
浅析中国古代宗法制度
g-C3N4光催化剂的制备和光催化性能研究
NFC协议物理层的软件实现+文献综述
上市公司股权结构对经营绩效的影响研究
C++最短路径算法研究和程序设计
高警觉工作人群的元情绪...
中国传统元素在游戏角色...