51单片机新型无刷直流电机控制器的设计+源程序
时间:2017-03-21 21:46 来源:毕业论文 作者:毕业论文 点击:次
| 摘要近年来，无刷直流电机以其效率高、噪声小、启动力矩大等优势，在电机领域得到了越来越广泛的应用，而电机控制器作为无刷直流电机的控制核心，其运转的高效性及稳定性也得到了人们较多的关注。本课题针对某单位自主研发的新型无刷直流电机，研制相应的控制器。6741 首先，本论文从常规无刷直流电动机控制器的整体组成方面结合该新型无刷直流电机的新型特点，设计出位置传感器的安装及使用方案和以单片机为核心的硬件控制电路。并详细介绍了系统外围电路、功率电路、逻辑保护电路等主要组成部分。 其次，对于软件部分首先论述了整体设计并给出了程序流程图，随后设计并给出了控制程序代码。 最后，对电机及其控制系统进行了空转调试，根据实验结果分析控制器及程序设计是否合理。 关键词 新型无刷直流电机，控制器设计，89C51单片机，大电流控制，串行接口 毕业设计说明书（论文）外文摘要 Title The controller design of the model Brushless DC motor Abstract In recent years,the brushless DC motor has been used more and more widely in the field of motor,because the brushless DC motor has the advantages of high efficiency,small noise,large starting torque and other advantages.The motor controller just works as the core of the control，and its operation efficiency and stability has been paid more and more attention.In this paper,my goal is to design the corresponding controller which is based on a company's new brushless DC motor . Firstly,this paper designs the position sensor installation with the use of corresponding program and the hardware control circuit which is mainly composed of the single-chip microcomputer.This design is according to the normal characteristic of conventional brushless DC motor controller and the new characteristic of new brushless DC motor model.And then this paper introduces the peripheral circuit, power circuit, protection circuit as the main elements of logic. Second , as for the software part,this paper discusses the overall design and gives the flow chart of the program firstly,then design and gives the control code. Finally, this paper will have the idle test based on the electric motor and its control system，and analyze whether the controller and program design is reasonable or not according to the experimental results. Key Words The Model Brushless DC motor , Drive design , 89C51 microcontroller , high-current control, serial interface 目 次 1. 绪论 1 1.1. 概述 1 1.1.1. 无刷直流电机的发展及应用 1 1.1.2. 无刷直流电机控制系统的发展 2 1.2. 无刷直流电机的基本原理及控制方式介绍 2 2. 新型无刷直流电机控制器系统设计 4 2.1. 新型无刷直流电机特点 4 2.2. 控制器系统方案设计 5 3. 新型无刷直流电机硬件电路设计 8 3.1. 单片机电路设计 8 3.2. 功率电路设计 10 3.3. 霍尔传感器选型及电路设计 12 3.4. 外围电路设计 15 3.4.1. 逻辑保护电路设计 15 3.4.2. 电源电路设计 15 3.5. 串口电路设计 16 3.6. 电机供电隔离设计 18 4. 新型无刷直流电机控制程序设计 19 5. 系统调试过程及结果 21 5.1. 实验系统组成 21 5.2. 软件工具介绍 22 5.2.1. Keil编译器 22 5.2.2. 单片机下载编程烧录软件 22 (责任编辑：qin) |