毕业论文移动版

摘  要本次设计的课题是汽车通气盖注塑模具。塑件确定采用聚丙烯（PP）为材料，该材料具有良好的绝缘性、较好的力学性能、较低廉的价格等优点，并且是最轻的通用塑料，较好的适用于汽车照明灯通气盖的制造。该设计使用了CAD、PROE、等多种设计绘图软件对汽车通气盖进行计算机软件辅助设计，使得塑件的设计生产更加快捷高效全面。本次设计分型面采用的是单分型面注塑模，型腔采用的是一模十六腔。该塑件浇口采用潜伏浇口注射，型芯的设计选用组合式型芯，塑件的推出机构选择一杆一板推出机构。69196

该论文有图17幅，表4个，参考文献25篇。

毕业论文关键词：通气盖  注射模具  设计  

Car ventilation cap injection mold design

Abstract

The topic of this design is the injection mold of the automobile ventilation cover. Plastic parts are determined using polypropylene (PP) as material. The material has good insulation, good mechanical properties, low price, etc., and is the lightest of general-purpose plastics and better applicable in car lighting ventilation cover manufacturing. This design uses the CAD, PROE, and so on many kinds of design drawing software to carry on the computer software aided design to the automobile ventilation cover, which makes the design and production of the plastic part more efficient and comprehensive. The design of the parting surface is a single injection mold parting surface, cavity using a mold sixteen cavity. The gate of plastics by submarine gate injection, the core with combined type core design, launched in the form of a rod plate pushing mechanism to complete the plastic parts to launch.

This paper has 16 figures, 4 tables, 22 references.

Key Words: Ventilation cover  Injection mold  Design

目  录

摘要Ⅰ

Abstract-Ⅱ

目录Ⅲ

图清单-Ⅳ

表清单-Ⅳ

1 绪论1

1.1注塑模具的基本概念1

1.2注塑模具的现状概况1

2 塑件成型工艺分析2

2.1塑件成型特性-2

2.2塑件结构工艺特性-2

2.3塑件的生产质量3

2.4关于注塑机3

3 分型面的选择和浇注系统的设计6

3.1选择分型面6

3.2设计主流道7

3.3设计分流道9

3.4设计浇口-9

3.5设计排气系统10

4 模具设计的方案论证11

4.1型腔的布局-11

4.2标准模架的选用-11

4.3支撑零部件设计-12

4.4合模导向机构13

4.5推出机构的设计-16

4.6组合镶件的设计-18

5 主要零部件的设计计算-19

5.1型腔尺寸设计计算19

5.2型芯尺寸设计计算19

5.3计算两圆弧间距的尺寸20

6 注射机有关参数校核21

6.1注射量的校核21

6.2锁模力的校核21

6.3模具与注塑机安装部分相关尺寸校核22

7 温度调节系统-23

7.1模具温度及其调节系统的重要性23

7.2冷却系统的结构-23

8 模具的工作27

8.1模具开合模过程工原理27

8.2模具的维护工作-27

9 结论-28

参考文献-29

致谢-31

图清单

图序号 图名称 页码

图2-1 汽车通气盖二维图样 3

图2-2 塑件的三维造型质量属性图 4

图3-1 塑件的分型面 6

图3-2 (责任编辑：qin)