毕业论文移动版

摘要：多工位级进模具是冲压模具的重要组成部分，把冲裁、弯曲、拉伸、成形工艺集成于一体的，代表现代先进生产方式的精密模具。本次毕业设计是支架成形工艺分析与多工位级进模设计，制件以操纵支架为对象，详细介绍从产品的工艺分析、计算数据及校核到最后模具设计的全过程。本此毕设课题联系现实实际生产，通过查阅大量文献及自学与模具设计相关的知识后，再进行多工位级进模具的设计。设计中主要运用了UG软件里的级进模模块，系统的完成从排样设计到模架、冲裁、弯曲、成形凸凹模和落料凹模的设计以及导柱、导套、螺钉、销钉的添加。完成模具设计后，进行仿真运行并加以改善模具，再次对模具及相关数据进行校核，确定模具设计合理。最后通过Autocad完成装配草图、装配工程图、零件工程图的制作，并进行总结撰写设计说明书。73751

毕业论文关键词：操纵支架；排样设计；级进模；冲压模设计 

Analysis of Stent Forming Process and Multi - Position Progressive Die

Abstract: Multi-station progressive die is an important part of the stamping die, the punching, bending, stretching, forming process integration in one, on behalf of modern advanced production mode of precision molds。 The graduation design is the stent forming process analysis and multi-station progressive die design, the workpiece to manipulate the bracket as the object, detailing from the product process analysis, calculation data and check to the final mold design of the whole process。 This is a separate project to contact the reality of the actual production, through access to a large number of literature and self-learning and mold design-related knowledge, and then multi-station progressive die design。 The design of the main use of the UG software in the progressive die module, the system from the nest design to mold, punching, bending, forming convex and die and blanking die design and guide column, guide sleeve, screws, pins To add。 After the completion of the mold design, simulation operation and to improve the mold, once again on the mold and related data to check to determine the mold design is reasonable。 Finally, through Autocad to complete the assembly sketch, assembly drawings, parts engineering drawings, and to write a summary of the design instructions。

Key words: Manipulate the bracket；Layout design；Progressive die；Stamping die design

目录

1前言 1

1。1 模具行业的发展现状 1

1。2 级进模 1

1。3课题意义及目的 2

2冲压工艺 3

2。1  制件的工艺性 3

2。1。1  制件材料及性能分析 3

2。1。2  制件的结构工艺性 3

2。1。3制件的尺寸精度 4

2。1。4制件的间断面的表面粗糙度 5

2。2冲压工艺方案 5

2。2。1工艺方案的拟定 5

2。2。2工艺方案的分析比较及确定 5

2。3 冲裁工艺计算 5

2。3。1展开件尺寸计算 5

2。3。2 搭边值的确定 6

2。3。3  排样设计 7

2。3。4 排样图的绘制 9

2。3。5 冲裁工艺力与压力中心 (责任编辑：qin)