ples were determined。

2。 Experimental setup

2。1。 Part

A box-shaped part that consists of some details such as ribs, holes, large flat surface, conical surface and rounded edge was adopted, in order to observe the effects of runner systems on its dimensions and shape。 The main dimensions of the part are 112 · 78 · 36 mm and the thickness of the walls is 2 mm。 The drawing and the general view of the part are presented in Fig。 1。

2。2。 Mould

In order to examine and to precisely compare the effects of HRS and CRS, it is necessary to perform the experiments at the same conditions。 Thus, a two-cavity mould which can be used with both HRS and CRS

was designed and produced。 The diameter of the nozzles was determined as 1。9 mm。 Six resistances of 400 W for heating the nozzles and manifold, and four thermocouples for controlling the melt temperature were fitted to the mould。 The determination of gate location was carried out by utilizing the Mold Flow analysis software for both HRS and CRS, as shown in Fig。 1。 For each mould cavity, four cooling channels with parallel connec- tion were generated。 The core and cavity halves of the mould are assumed to have the same temperature to minimize warpage。 After completion of the experiments with HRS, the mould was modified for CRS by assem- bling some appropriate components such as sprue pulling pin and plugs for nozzle nests。 Thus, the possibility of doing all experiments with both runner systems on the same mould and comparison of the results precisely were provided。

2。3。 Injection  machine  and materials

An injection moulding machine having a clamping force of 80 tonnes and a shot capacity of 170 g。 was used for the experiments。 In the exper- iments, acrylonitrile butadiene styrene (ABS) and polypropylene (PP) polymers were used。 ABS is an amorphous polymer produced by GE Plas- tics, and PP is a semi-crystalline polymer produced by Petkim A。S。 Of some major specifications, the process temperature range is 220–280 °C

for ABS and 170–260 °C for PP, and the melt flow index is 3。7 g/10 min

for ABS and 6 g/10 min for PP。 The detailed specifications of these poly- mers are listed in Table  1。

3。 Determination of optimal moulding area

The experimental study was carried out in a wide range of temperatures recommended by the manufacturer of the material。 Within this range, both melting point and decom- position limit of the material were taken into consideration。 The value of packing pressure was determined to be half of the injection pressure, and the other  parameters  (i。e。, mould temperature, injection velocity and cycle time) were kept constant during all experiments for both runner sys- tems。 The process conditions adopted in the experiments are presented in Table  2。

Injection moulding processes were performed at three stages。 In the first stage, achievable minimum and maxi- mum values of injection pressure were determined by heat- ing the material on the injection moulding machine to a minimum temperature at which it can  be  injected。 Then, the same procedure was repeated for mean and maximum process temperatures。 In order to determine optimal pro- cess area for HRS in comparison with CRS, moulding area diagrams (MAD) were drawn on the bases of the data obtained from the experiments。 Produced samples relating to various MAD regions are shown in Fig。 2。 The MADs for ABS and PP polymers are  shown  in  Figs。  3  and 4。 The lower and upper limits of the process variables used in the MADs were determined so that there would neither be a flash formation nor short shot in the injected part as well as no chemical degradation。 The regions that are located to the left of and under the closed areas on these diagrams represent the short shot in  the  injected  part at low pressure and low temperature  (i。e。,  top  in  Fig。  2)。 The regions that are located to the right of and above the closed areas represent the flash formation in the injected part at high  pressure  and  high  temperature  (i。e。, middle in  Fig。  2)。  The  closed  areas  represent  the     appropriate

上一篇:塑料盖镜片残余应力的消除英文文献和中文翻译
下一篇:大学毕业生工作选择英文文献和中文翻译

轨道转化砂带的砂光机英文文献和中文翻译

基卡气体管道PLEM结构的原...

除尘式道路清洁机英文文献和中文翻译

垂直轴冲击式破碎机转子...

注塑模具内流道压力与型...

监测和诊断多通道非线性...

压力阀迷宫通道流量特性英文文献和中文翻译

麦秸秆还田和沼液灌溉对...

张洁小说《无字》中的女性意识

老年2型糖尿病患者运动疗...

安康汉江网讯

ASP.net+sqlserver企业设备管理系统设计与开发

网络语言“XX体”研究

我国风险投资的发展现状问题及对策分析

LiMn1-xFexPO4正极材料合成及充放电性能研究

新課改下小學语文洧效阅...

互联网教育”变革路径研究进展【7972字】